从本小节开始，讲着重介绍Zedboard上的嵌入式linux应用，包括使用SDK设计最简单的linux应用程序、linux交叉编译环境搭建、设备驱动编写等内容。本小节使用的linux系统是Digilent官方提供的OOB设计，它是Digilent官网给出的一个完整的、Zedboard可运行的linux系统，包含了Zedboard上的几个重要的设备驱动如串口、USB、以太网、OLED、HDMI等。当linux在Zedboard上运行起来后，Zedboard就是一个小型的嵌入式系统，使用SDK及Xilinx ARM Linux工具链编译生成的可执行文件可以在这个系统执行。 硬件平台：Digilent ZedBoard
开发环境：Windows XP 32 bit
软件： SDK 14.2
一、获取Zedboard可运行的linux Digilent官网给出Zedboard的可运行linux设计ZedBoard_OOB_Design包，可从http://www.digilentinc.com/Data/Documents/Other/ZedBoard_OOB_Design.zip 获取，下载后解压，可以看到包的结构和内容：boot_image目录: -- system.bit – 配置FPGA的bit文件-- u-boot.elf – 引导linux需要的Second-Stage boot loader-- zynq_fsbl.elf – 配置ARM PS系统的First-Stage boot loader(FSBL)doc目录:-- README.txt – 说明文件hw目录:-- EDK 14.1版本的XPS工程，用来生成硬件文件和bit文件linux目录:-- devicetree_ramdisk.dts – 设备树源代码-- .config – Linux内核配置文件，用来生成zImagesd_image目录:-- BOOT.BIN – 使用boot_images中的三个文件生成的Zynq配置文件-- devicetree_ramdisk.dtb – 编译后的设备树文件-- ramdisk8M.image.gz – 编译后的文件系统-- README – 介绍如何运行OOB设计的说明文档-- zImage – 编译后的内核sw目录:--硬件配置--FSBL源代码 其中sd_image目录中包含了ZedBoard上能够运行linux的所有文件。将SD卡格式化为Fat32，把sd_image目录文件拷贝到SD卡根目录下；然后将JP7~JP11设置为SD卡启动模式，将JP2短路，JP3断开，这样可以下一步我们可以把U盘作为USB 从设备挂载到Zedboard上。[[wysiwyg_imageupload:779:]] 上电后，等待ARM PS的配置、FPGA的配置(蓝色LED DONE 亮起)，之后开始引导Linux系统了。可以从超级终端上看到一系列的引导信息：U-Boot 2012.04.01-00297-gc319bf9-dirty (Sep 13 2012 - 09:30:49) DRAM: 512 MiB WARNING: Caches not enabled MMC: SDHCI: 0 Using default environment In: serial Out: serial Err: serial Net: zynq_gemHit any key to stop autoboot: 0 Copying Linux from SD to RAM... Device: SDHCI Manufacturer ID: 1b OEM: 534d Name: 00000 Tran Speed: 25000000 Rd Block Len: 512 SD version 1.0 High Capacity: Yes Capacity: 3.7 GiB Bus Width: 1-bit reading zImage 2479640 bytes read reading devicetree_ramdisk.dtb 5817 bytes read reading ramdisk8M.image.gz 3694108 bytes read ## Starting application at 0x00008000 ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.3.0-digilent-12.07-zed-beta (tinghui.wang@DIGILENT_LINUX) (gcc version 4.6.1 (Sourcery CodeBench Lite 2011.09-50) ) #2 SMP PREEMPT Thu Jul 12 21:01:42 PDT 2012 [ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Xilinx Zynq Platform, model: Xilinx Zynq ZED [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] BUG: mapping for 0xf8f00000 at 0xfe00c000 out of vmalloc space [ 0.000000] BUG: mapping for 0xe0000000 at 0xfe000000 out of vmalloc space [ 0.000000] BUG: mapping for 0xffff1000 at 0xfe200000 out of vmalloc space [ 0.000000] PERCPU: Embedded 7 pages/cpu @c1489000 s5696 r8192 d14784 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125824 [ 0.000000] Kernel command line: console=ttyPS0,115200 root=/dev/ram rw initrd=0x800000,8M earlyprintk rootfstype=ext4 rootwait devtmpfs.mount=0 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 240MB 256MB = 496MB total [ 0.000000] Memory: 489856k/489856k available, 34432k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xfd000000 ( 456 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc042f040 (4253 kB) [ 0.000000] .init : 0xc0430000 - 0xc0456640 ( 154 kB) [ 0.000000] .data : 0xc0458000 - 0xc0485dc0 ( 184 kB) [ 0.000000] .bss : 0xc0485de4 - 0xc049d734 ( 95 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Verbose stalled-CPUs detection is disabled. [ 0.000000] NR_IRQS:128 [ 0.000000] xlnx,ps7-ttc-1.00.a #0 at 0xe0800000, irq=43 [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816) [ 0.090000] pid_max: default: 32768 minimum: 301 [ 0.090000] Mount-cache hash table entries: 512 [ 0.090000] CPU: Testing write buffer coherency: ok [ 0.090000] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.100000] smp_twd: clock not found: -2 [ 0.100000] Calibrating local timer... 399.36MHz. [ 0.170000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 0.170000] Setting up static identity map for 0x2f8d48 - 0x2f8d7c [ 0.270000] CPU1: Booted secondary processor [ 0.310000] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.310000] Brought up 2 CPUs [ 0.310000] SMP: Total of 2 processors activated (3188.32 BogoMIPS). [ 0.320000] devtmpfs: initialized [ 0.320000] ------------[ cut here ]------------ [ 0.320000] WARNING: at arch/arm/mm/dma-mapping.c:198 consistent_init+0x70/0x104() [ 0.330000] Modules linked in: [ 0.330000] [<c0012920>] (unwind_backtrace+0x0/0xe0) from [<c001e924>] (warn_slowpath_common+0x4c/0x64) [ 0.340000] [<c001e924>] (warn_slowpath_common+0x4c/0x64) from [<c001e954>] (warn_slowpath_null+0x18/0x1c) [ 0.350000] [<c001e954>] (warn_slowpath_null+0x18/0x1c) from [<c04345a8>] (consistent_init+0x70/0x104) [ 0.360000] [<c04345a8>] (consistent_init+0x70/0x104) from [<c000858c>] (do_one_initcall+0x90/0x160) [ 0.360000] [<c000858c>] (do_one_initcall+0x90/0x160) from [<c043085c>] (kernel_init+0x84/0x128) [ 0.370000] [<c043085c>] (kernel_init+0x84/0x128) from [<c000dfcc>] (kernel_thread_exit+0x0/0x8) [ 0.380000] ---[ end trace 1b75b31a2719ed1c ]--- [ 0.380000] ------------[ cut here ]------------ [ 0.390000] WARNING: at arch/arm/mm/dma-mapping.c:198 consistent_init+0x70/0x104() [ 0.390000] Modules linked in: [ 0.390000] [<c0012920>] (unwind_backtrace+0x0/0xe0) from [<c001e924>] (warn_slowpath_common+0x4c/0x64) [ 0.400000] [<c001e924>] (warn_slowpath_common+0x4c/0x64) from [<c001e954>] (warn_slowpath_null+0x18/0x1c) [ 0.410000] [<c001e954>] (warn_slowpath_null+0x18/0x1c) from [<c04345a8>] (consistent_init+0x70/0x104) [ 0.420000] [<c04345a8>] (consistent_init+0x70/0x104) from [<c000858c>] (do_one_initcall+0x90/0x160) [ 0.430000] [<c000858c>] (do_one_initcall+0x90/0x160) from [<c043085c>] (kernel_init+0x84/0x128) [ 0.430000] [<c043085c>] (kernel_init+0x84/0x128) from [<c000dfcc>] (kernel_thread_exit+0x0/0x8) [ 0.440000] ---[ end trace 1b75b31a2719ed1d ]--- [ 0.440000] NET: Registered protocol family 16 [ 0.460000] L310 cache controller enabled [ 0.460000] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72060000, Cache size: 524288 B [ 0.460000] registering platform device 'pl330' id 0 [ 0.470000] registering platform device 'arm-pmu' id 0 [ 0.470000] [ 0.470000] ############################################### [ 0.480000] # # [ 0.480000] # Board ZED Init # [ 0.480000] # # [ 0.490000] ############################################### [ 0.490000] [ 0.500000] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpointregisters. [ 0.500000] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.530000] xslcr xslcr.0: at 0xF8000000 mapped to 0xE0808000 [ 0.540000] bio: create slab <bio-0> at 0 [ 0.540000] gpiochip_add: registered GPIOs 0 to 245 on device: xgpiops [ 0.540000] xgpiops e000a000.gpio: gpio at 0xe000a000 mapped to 0xe080a000 [ 0.550000] SCSI subsystem initialized [ 0.550000] usbcore: registered new interface driver usbfs [ 0.560000] usbcore: registered new interface driver hub [ 0.560000] usbcore: registered new device driver usb [ 0.570000] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.570000] Switching to clocksource xttcpss_timer1 [ 0.590000] NET: Registered protocol family 2 [ 0.590000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.590000] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.600000] TCP bind hash table entries: 16384 (order: 5, 196608 bytes) [ 0.600000] TCP: Hash tables configured (established 16384 bind 16384) [ 0.610000] TCP reno registered [ 0.610000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.620000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.620000] NET: Registered protocol family 1 [ 0.630000] Trying to unpack rootfs image as initramfs... [ 0.630000] rootfs image is not initramfs (no cpio magic); looks like an initrd [ 0.670000] Freeing initrd memory: 8192K [ 0.670000] xscugtimer xscugtimer.0: ioremap fe00c200 to e0810200 with size 400 [ 0.670000] pl330 dev 0 probe success [ 0.680000] msgmni has been set to 972 [ 0.680000] io scheduler noop registered [ 0.680000] io scheduler deadline registered [ 0.680000] io scheduler cfq registered (default) [ 0.690000] e00 0.690000] console [ttyPS0] enabled, bootconsole disabled [ 0.690000] console [ttyPS0] enabled, bootconsole disabled [ 0.700000] xdevcfg f8007000.devcfg: ioremap f8007000 to e0814000 with size 1000 [ 0.710000] [drm] Initialized drm 1.1.0 20060810 [ 0.720000] brd: module loaded [ 0.730000] loop: module loaded [ 0.730000] xqspips e000d000.qspi: at 0xE000D000 mapped to 0xE0816000, irq=51 [ 0.740000] GEM: BASEADDRESS hw: e000b000 virt: e0818000 [ 0.740000] XEMACPS mii bus: probed [ 0.750000] eth0, pdev->id -1, baseaddr 0xe000b000, irq 54 [ 0.750000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.760000] usb_hcd_xusbps_probe: No OTG assigned! [ 0.760000] usb_hcd_xusbps_probe: OTG now assigned! [ 0.770000] xusbps-ehci xusbps-ehci.0: Xilinx PS USB EHCI Host Controller [ 0.770000] xusbps-ehci xusbps-ehci.0: new USB bus registered, assigned bus number 1 [ 0.810000] xusbps-ehci xusbps-ehci.0: irq 53, io mem 0x00000000 [ 0.830000] xusbps-ehci xusbps-ehci.0: USB 2.0 started, EHCI 1.00 [ 0.830000] hub 1-0:1.0: USB hub found [ 0.830000] hub 1-0:1.0: 1 port detected [ 0.840000] Initializing USB Mass Storage driver... [ 0.840000] usbcore: registered new interface driver usb-storage [ 0.850000] USB Mass Storage support registered. [ 0.850000] Xilinx PS USB Device Controller driver (Apr 01, 2011) [ 0.860000] mousedev: PS/2 mouse device common for all mice [ 0.860000] Linux video capture interface: v2.00 [ 0.870000] gspca_main: v2.14.0 registered [ 0.870000] usbcore: registered new interface driver uvcvideo [ 0.870000] USB Video Class driver (1.1.1) [ 0.880000] WDT OF probe [ 0.880000] xwdtps f8005000.swdt: Xilinx Watchdog Timer at 0xe081c000 with timeout 10 seconds [ 0.890000] sdhci: Secure Digital Host Controller Interface driver [ 0.890000] sdhci: Copyright(c) Pierre Ossman [ 0.900000] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.900000] mmc0: Invalid maximum block size, assuming 512 bytes [ 0.910000] mmc0: SDHCI controller on e0100000.sdhci [e0100000.sdhci] using ADMA [ 0.910000] usbcore: registered new interface driver usbhid [ 0.920000] usbhid: USB HID core driver [ 0.920000] No connectors reported connected with modes [ 0.930000] adv7511 0-0039: Failed to add route DAI IN->TMDS [ 0.940000] [drm] Cannot find any crtc or sizes - going 1024x768 [ 0.940000] drivers/gpu/drm/analog/analog_drm_fbdev.c:analog_drm_fbdev_probe[241] [ 0.960000] asoc: adv7511 <-> 75c00000.axi-spdif-tx mapping ok [ 0.960000] axi-spdif 75c00000.axi-spdif-tx: Failed to set DAI format: -22 [ 0.980000] ALSA device list: [ 0.980000] #0: HDMI monitor [ 0.980000] TCP cubic registered [ 0.980000] NET: Registered protocol family 17 [ 0.980000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.980000] Registering SWP/SWPB emulation handler [ 0.980000] registered taskstats version 1 [ 0.980000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 0.980000] Console: switching to colour frame buffer device 128x48 [ 1.000000] mmc0: new high speed SDHC card at address 0002 [ 1.030000] fb0: frame buffer device [ 1.030000] mmcblk0: mmc0:0002 00000 3.70 GiB [ 1.040000] drm: registered panic notifier [ 1.040000] [drm] Initialized analog_drm 1.0.0 20110530 on minor 0 [ 1.050000] mmcblk0: p1 [ 1.050000] RAMDISK: gzip image found at block 0 [ 1.310000] EXT4-fs (ram0): warning: mounting unchecked fs, running e2fsck is recommended [ 1.320000] EXT4-fs (ram0): mounted filesystem without journal. Opts: (null) [ 1.320000] VFS: Mounted root (ext4 filesystem) on device 1:0. [ 1.330000] Freeing init memory: 152K Starting rcS... ++ Mounting filesystem ++ Setting up mdev ++ Configure static IP 192.168.1.10 [ 1.510000] GEM: lp->tx_bd ffdfb000 lp->tx_bd_dma 181a9000 lp->tx_skb d816b0c0 [ 1.520000] GEM: lp->rx_bd ffdfc000 lp->rx_bd_dma 181a8000 lp->rx_skb d816b1c0 [ 1.520000] GEM: MAC 0x00350a00, 0x00002201, 00:0a:35:00:01:22 [ 1.530000] GEM: phydev d8b81400, phydev->phy_id 0x1410dd1, phydev->addr 0x0 [ 1.540000] eth0, phy_addr 0x0, phy_id 0x01410dd1 [ 1.540000] eth0, attach [Marvell 88E1510] phy driver ++ Starting telnet daemon ++ Starting http daemon ++ Starting ftp daemon ++ Starting dropbear (ssh) daemon ++ Starting OLED Display [ 1.580000] pmodoled-gpio-spi [zed_oled] SPI Probing [ 1.730000] usb 1-1: new high-speed USB device number 2 using xusbps-ehci ++ Exporting LEDs & SWs rcS Complete zynq> 至此，linux已经在Zedboard上启动起来。从超级终端输出的信息我们打开可以知道，“这个”linux系统的一些基本情况，如8~10行In: serialOut: serialErr: serial 输入输出调试信息使用的都是serial，即串口，这里是超级终端，因而超级终端就如同linux系统下的控制台，我们可以键入linux的命令对系统进行操作，例如输入ls命令，可以显示当前目录内容：[[wysiwyg_imageupload:780:]] 其他命令如cd、mkdir、cp、rm等基本命令均可以执行。 77~79行提示信息 [ 0.270000] CPU1: Booted secondary processor[ 0.310000] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001[ 0.310000] Brought up 2 CPUs 可以知道ARM PS的两个CPU均被启动 再如163~171行 [ 0.840000] Initializing USB Mass Storage driver...[ 0.840000] usbcore: registered new interface driver usb-storage[ 0.850000] USB Mass Storage support registered.[ 0.850000] Xilinx PS USB Device Controller driver (Apr 01, 2011)[ 0.860000] mousedev: PS/2 mouse device common for all mice[ 0.860000] Linux video capture interface: v2.00[ 0.870000] gspca_main: v2.14.0 registered[ 0.870000] usbcore: registered new interface driver uvcvideo[ 0.870000] USB Video Class driver (1.1.1) 可以知道大容量USB设备驱动已经安装，包括PS USB设备等驱动均安装了，因此可以使用U盘、USB键盘、鼠标、摄像头等设备。 二、使用SDK设计linux应用程序 接下来我们就可以像其他的嵌入式linux开发一样来使用Zedboard了。SDK提供了标准可视化的linux-arm交叉编译链，不需要再进行交叉编译环境的搭建。 启动SDK，new->C project，选择工程类型为“Xilinx ARM Linux Executable”，工具链为“Xilinx ARM GNU/Linux Toolchain”[[wysiwyg_imageupload:781:]] 在工程配置选项中，去掉Debug(因为我们不需要进行调试)，只保留Release[[wysiwyg_imageupload:782:]] 工程建立后好，新建main.c文件，修改内容如下：/* * hello.c * * Created on: 2012-11-8 * @超群天晴 http://www.cnblogs.com/surpassal/ */ #include <stdio.h> int main() { printf("HelloWorld!\n"); printf("This is from Zedboard Linux!\n"); printf("2012年11月8日16:43:22 by 超群天晴\n"); return 0; } 就是一个简单的从控制台输出helloworld信息。编译后生成了lab_6.elf可执行文件，将其拷贝到了U盘上。 三、运行linux可执行程序 将U盘连接到Zedboard，控制台会提示有USB device连接上，分配给这个设备的名称是sda1 zynq> [ 2263.970000] usb 1-1: new high-speed USB device number 2 using xusbps-ehci [ 2264.120000] scsi0 : usb-storage 1-1:1.0 [ 2265.130000] scsi 0:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 4 [ 2265.140000] sd 0:0:0:0: [sda] 3932160 512-byte logical blocks: (2.01 GB/1.87GiB) [ 2265.140000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2265.150000] sd 0:0:0:0: [sda] Write Protect is off [ 2265.150000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 2265.170000] sda: sda1 [ 2265.180000] sd 0:0:0:0: [sda] Attached SCSI removable disk zynq> 使用mount命令 mount /dev/sda1 /mnt/ 将设备挂载到mnt目录下， 输入命令 cd /mnt切换到mnt目录 输入命令 ls可以看到目录下有我们刚刚生成的lab_6.elf可执行文件 输入命令 ./lab_6.elf 运行，可以看到执行结果，控制台输出了我们需要的信息[[wysiwyg_imageupload:783:]] Digilent官方OOB设计参考：http://www.digilentinc.com/Data/Documents/Other/ZedBoard_OOB_Design.zip完整工程下载：lab_6.rar来源：超群天晴的博客 |
